diff options
119 files changed, 12550 insertions, 2698 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt new file mode 100644 index 000000000000..928ed4f43907 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt @@ -0,0 +1,47 @@ +* Oxford Semiconductor OXNAS SoC GPIO Controller + +Please refer to gpio.txt for generic information regarding GPIO bindings. + +Required properties: + - compatible: "oxsemi,ox810se-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - gpio-ranges: Interaction with the PINCTRL subsystem, it also specifies the + gpio base and count, should be in the format of numeric-gpio-range as + specified in the gpio.txt file. + +Example: + +gpio0: gpio@0 { + compatible = "oxsemi,ox810se-gpio"; + reg = <0x000000 0x100000>; + interrupts = <21>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&pinctrl 0 0 32>; +}; + +keys { + ... + + button-esc { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt index e4277921f3e3..a73cbeb0f309 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt @@ -3,8 +3,22 @@ Broadcom iProc GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", - "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" + "brcm,iproc-gpio" for the generic iProc based GPIO controller IP that + supports full-featured pinctrl and GPIO functions used in various iProc + based SoCs + + May contain an SoC-specific compatibility string to accommodate any + SoC-specific features + + "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or + "brcm,cygnus-crmu-gpio" for Cygnus SoCs + + "brcm,iproc-nsp-gpio" for the iProc NSP SoC that has drive strength support + disabled + + "brcm,iproc-stingray-gpio" for the iProc Stingray SoC that has the general + pinctrl support completely disabled in this IP block. In Stingray, a + different IP block is used to handle pinctrl related functions - reg: Define the base and range of the I/O address space that contains SoC diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt new file mode 100644 index 000000000000..603564e5fe6f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt @@ -0,0 +1,79 @@ +Broadcom NSP (Northstar plus) IOMUX Controller + +The NSP IOMUX controller supports group based mux configuration. In +addition, certain pins can be muxed to GPIO function individually. + +Required properties: +- compatible: + Must be "brcm,nsp-pinmux" + +- reg: + Should contain the register physical address and length for each of + GPIO_CONTROL0, GP_AUX_SEL and IPROC_CONFIG IOMUX registers + +Properties in subnodes: +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinmux: pinmux@1803f1c0 { + compatible = "brcm,nsp-pinmux"; + reg = <0x1803f1c0 0x04>, + <0x18030028 0x04>, + <0x1803f408 0x04>; + + pinctrl-names = "default"; + pinctrl-0 = <&pwm &gpio_b &nand_sel>; + + pwm: pwm { + function = "pwm"; + groups = "pwm0_grp", "pwm1_grp"; + }; + + gpio_b: gpio_b { + function |